|
335
|
Ultimate Audio Playback / XXHighEnd Support / Re: 0.9z-7-3 Sample Rate not set
|
on: September 14, 2012, 08:08:05 am
|
|
Hi Peter,
Ok its like this. When I start the PC, Load playlist & click start I get the msg (attached). If I stop & click play again then the msg does not come back. So it comes at the first play only.
It doesnt matter if engine #3 is killed or running. In both case the msg appears at the first play.
Hope this helps.
Best regards,
Arvind
|
|
|
|
|
338
|
Ultimate Audio Playback / XXHighEnd Support / 9Z7-2 Still crack Issue Phase Alignment
|
on: September 04, 2012, 05:14:22 pm
|
|
Hi Peter,
In my case 0.9z7-2 hasn't solved the problem of a couple of clicks at start of the first track, neither a louder click after 10 seconds & neither a couple of loud clicks after 20 to 30 mins of playback. CPU doesn't indicate any abnormal activity.
Tried increasing Q1 to 30, SFS to 60, but no change.
Any suggestions?
Best regards,
Arvind
|
|
|
|
|
340
|
Ultimate Audio Playback / XXHighEnd Support / Re: 0.9z-7-2 OS doesn't minimise
|
on: August 31, 2012, 09:54:25 am
|
Hey Arvind,
Nothing changed and it just should work (and does so here).
Maybe you are not properly Activated ?
Regards,
Peter
Hi Peter, Like the earlier versions I copy pasted the Activation code (dat file) into 0.9z-7-2 folder. So I guess this was wrong, I need to once again enter the activation code & follow the Activation procedure. Is this the way? Best regards, Arvind |
|
|
|
|
342
|
Ultimate Audio Playback / XXHighEnd Support / Re: Problems with RDC
|
on: August 28, 2012, 06:24:59 am
|
Arvind,
If you go to the Bluetooth icon in the Taskbar Tray (see first picture below, so only *that* icon) and you rightclick on it and choose "open settings" ... are your settings the same as you see in the second picture below ?
All I know is that this is default, but maybe it is not.
Don't forget to check both the PC and the laptop.
Regards,
Peter
Hi Peter, The problem in my case was that by default it does not allow A Bluetooth device to connect. Hence I had to tick that & I have managed to connect both devices. Now I will move fwd in the tutorials. Thanks for the help. Best regards, Arvind |
|
|
|
|
344
|
Ultimate Audio Playback / XXHighEnd Support / Re: Problems with RDC
|
on: August 27, 2012, 03:59:55 pm
|
Ok. Do both of the dongles show a blinking led (that can be not regularly blinking) ?
Do you have any other Bluetooth device in the house ? can easily be a phone. Switch it on and make it "detectable" (if you can find the choice) and from either PC try to find it in the same screen as you showed. Notice that "from either PC" is two-folded :
1. There might be something wrong with the driver install after all (not likely);
2. There might be something wrong with one of the dongles.
The above should give you the opportunity to find out what is wrong (hoping that you will at least now see something somewhere). So, dongle or install - and you will find out by swapping the dongles and see things happen on the PC's in question.
Notice that it can even be a USB port not working (internally not connected). And of course USB2 should be active, might you have gone the USB3 route with the NOS1.
Also keep in mind the line of sight which must be there.
Lastly, once you saw a device, keep in mind that at swapping things it will still show, no matter it can't be seen anymore. So, always remove the Bluetooth device first at a next (swap) attempt (this is in the Tutorial, just preceeding the screenshots I just showed).
Well ... ?
Kind regards,
Peter
Hi Peter, Both dongles blink for some time then the blinking stops for some time & restarts again. I put on the Bluetooth on my mob phone & both the Audio PC as well as the Laptop discovered the device. (screen shot of audio PC is attached). Next I interchanged the two blue tooth devices after switching off the Blurtooth from my mob phone. Performed the same again, activated the Bluetooth on my mob phone & once again the Audio PC as well as the laptop discovered them. So I assume that the bluetooth devices are ok. However the two computers do not discover each other as yet. Line of sight between the 2 bluetooth device is clear. Best regards, Arvind |
|
|
|
|
Show Posts
